Salsa 1 Power
- Salsa 1 DC Extension Cable
- Salsa 1 Power Supply
- Salsa 1 AC Power Cable
- Salsa 1 iPad Charging Cable (USB-C)
Salsa 1 Head
- Salsa 1 Faceplate Screws
- Salsa 1 Tilt Lever
- Salsa 1 Tilt Lever Nut
- Salsa 1 Jack Port Retention Nut
- Salsa 1 Hinge Knob
- 12.9" iPad Pro Salsa 1 Faceplate
- 11" iPad Pro & 10.9" iPad Air Salsa 1 Faceplate
Salsa 1 Poles
Salsa 1 Base Plate
Atlas Backdrop Stand
Miscellaneous
Salsa 1 Power
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement Salsa 1 power parts.
Salsa 1 DC Extension Cable
The cable that connects to the bottom of the Salsa 1 Head and the Salsa 1 Power Supply. It delivers power directly to the Salsa 1 Head.
Where To Purchase:
Salsa 1 Power Supply
The device that connects the Salsa 1 DC Extension Cable to the Salsa 1 AC Power Cable. It converts incoming power from the wall outlet or battery into usable energy for the Salsa 1 Booth.
Where To Purchase:
Salsa 1 AC Power Cable
This cable connects the Salsa 1 Power Supply to a power source - such as a wall outlet or battery, to complete the booth's power connection.
Where To Purchase:
Salsa 1 iPad Charging Cable (USB-C)
This cable is used to charge the iPad while it is mounted inside the Salsa 1 Head.
Where To Purchase:
Salsa 1 Head
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Head.
Salsa 1 Faceplate Screws
Secures the Salsa 1 Faceplate to the front of the Salsa 1 Head.
Details:
Black-Oxide 18-8 Stainless Steel Phillips Flat Head Screws
Thread size #6-32
Original screw length: 7/8"
Where To Purchase:
- McMaster (original screw length, 7/8")
- Amazon (slightly shorter than the original screw length, 3/4" - still compatible with the Salsa 1 Faceplate)
Salsa 1 Tilt Lever
The device used to tighten or loosen the hinge, allowing you to adjust the angle of the Salsa 1 Head.
Where To Purchase:
Salsa 1 Tilt Lever Nut
This nut secures the Salsa 1 Tilt Lever to the Salsa 1 Hinge, keeping it firmly in place.
Where To Purchase:
Salsa 1 Jack Port Retention Nut
This nut secures the Salsa 1 Jack Port on the bottom of the Salsa 1 Head, where the Salsa 1 DC Extension Cable connects. It keeps the power connection port firmly in place.
Where To Purchase:
Salsa 1 Hinge Knob
Knobs located on both sides of the Salsa 1 Hinge, used to secure and tighten the Salsa 1 Head to the Salsa 1 Poles.
Where To Purchase:
- McMaster
- Amazon (Similar to the original supplier, but of a lower quality. Will function identically)
12.9" iPad Pro Salsa 1 Faceplate
Front cover for Salsa 1 Photo Booths that secure 12.9" iPad Pro 3rd - 6th Generation (2018 - 2022) to the Salsa 1 Head.
Where To Purchase:
11" iPad Pro & 10.9" iPad Air Salsa 1 Faceplate
Front cover for Salsa 1 Photo Booths that secure 11" iPad Pro 1st - 4th Generation (2018 - 2022), and 10.9" iPad Air 4th - 5th Generation (2020 - 2022) to the Salsa 1 Head.
Where To Purchase:
Salsa 1 Poles
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Poles.
Salsa 1 Hinge Knob And Pole Rod Retention Nut
This nut is located within the Salsa 1 Poles and beneath the Salsa 1 Hinge Knobs. It tightens the internal rods, helping to secure the poles to the baseplate, to each other, and to the Salsa 1 Hinge.
Where To Purchase:
Replacement Poles
These replacement poles can be purchased if one or both of the original Salsa 1 poles become scratched, lost, or damaged.
Where To Purchase:
Salsa 1 Base Plate
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Base Plate.
Salsa 1 Base Plate Feet
Set of adhesive feet measuring 3/4" wide by 3/4" long and 3/8" high, designed to attach to the bottom of the Salsa 1 Base Plate for added grip and stability on various surfaces.
Where To Purchase:
Salsa 1 Base Plate Feet Adhesive
This adhesive tape is used to attach the Salsa 1 Base Plate Feet to the Salsa 1 Baseplate in cases where the adhesive has worn out.
Where To Purchase:
IMPORTANT: The adhesive is designed to be used with the Salsa 1 Base Plate Feet and will require trimming, as it does not come pre-cut. For best results, clean the Salsa 1 Base Plate surface thoroughly with a mild solvent before applying.
Atlas Backdrop Stand
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Atlas Backdrop Stand.
Bottom Atlas Stand Pole Screw
These screws attach to the bottom of the Atlas Stand under the feet.
Details:
M8-1.25 x 45mm flat head socket cap screws countersunk bolt
Where To Purchase:
IMPORTANT: Any M8-1.25 screw with a length between 30mm and 50mm is compatible with the bottom pole of the Atlas Stand.
Miscellaneous
Below is a list of all of Photobooth Supply Co.'s official recommendations for miscellaneous parts used with Salsa 1 Photo Booth.
Salsa 1 SKB Carrying Case
This carrying case is a hard shell case designed for transporting the Salsa 1 Booth.
Where To Purchase:
IMPORTANT: The foam inserts included with the original Salsa 1 SKB case are custom-made and proprietary to Photobooth Supply Co.
These custom-made foam inserts are not available for purchase through the Midwest Case Company and are not included if you purchase a new SKB hard shell carrying case directly.
If you need to replace your case, we recommend removing and reusing the original foam from your current Salsa 1 Booth.
If your Salsa 1 carrying case is damaged or needs replacement parts, you can reach out directly to SKB Cases to submit a request.
Top Button/Home Button Tool
This tool is used to press the sleep/wake (top) button or home button through the opening in the Salsa 1 Faceplate to activate or exit Guided Access mode.
Where To Purchase: