Salsa 1 Power
- Salsa 1 DC Extension Cable
- Salsa 1 Power Supply
- Salsa 1 AC Power Cable
- Salsa 1 iPad Charging Cable (USB-C)
Salsa 1 Head
- Salsa 1 Faceplate Screws
- Salsa 1 Tilt Lever
- Salsa 1 Tilt Lever Nut
- Salsa 1 Jack Port Retention Nut
- Salsa 1 Hinge Knob
- 12.9" iPad Pro Salsa 1 Faceplate
- 11" iPad Pro & 10.9" iPad Air Salsa 1 Faceplate
Salsa 1 Poles
Salsa 1 Base Plate
Atlas Backdrop Stand
Miscellaneous
Salsa 1 Power
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement Salsa 1 power parts.
Salsa 1 DC Extension Cable
This cable connects the Salsa 1 Power Supply to the bottom of the Salsa 1 Head and delivers power to the booth.
Where To Purchase:
Salsa 1 Power Supply
This power supply connects the Salsa 1 DC Extension Cable to the Salsa 1 AC Power Cable and converts incoming power into usable power for the booth.
Where To Purchase:
Salsa 1 AC Power Cable
This cable connects the Salsa 1 Power Supply to a wall outlet or battery to complete the booth’s power connection.
Where To Purchase:
Salsa 1 iPad Charging Cable (USB-C)
This cable charges the iPad while it is mounted inside the Salsa 1 Head.
Where To Purchase:
Salsa 1 Head
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Head.
Salsa 1 Faceplate Screws
These screws secure the Salsa 1 Faceplate to the front of the Salsa 1 Head.
Details:
- Black-Oxide 18-8 Stainless Steel Phillips Flat Head Screws
- Thread size #6-32
- Original screw length: 7/8"
Where To Purchase:
- McMaster (original screw length, 7/8")
- Amazon (slightly shorter than the original screw length, 3/4" - still compatible with the Salsa 1 Faceplate)
Salsa 1 Tilt Lever
This lever tightens or loosens the hinge to adjust the angle of the Salsa 1 Head.
Where To Purchase:
Salsa 1 Tilt Lever Nut
This nut secures the Salsa 1 Tilt Lever to the Salsa 1 Hinge, keeping it firmly in place.
Where To Purchase:
Salsa 1 Jack Port Retention Nut
This nut secures the Salsa 1 Jack Port on the bottom of the Salsa 1 Head, where the Salsa 1 DC Extension Cable connects. It keeps the power connection port firmly in place.
Where To Purchase:
Salsa 1 Hinge Knob
These knobs are located on both sides of the Salsa 1 Hinge and secure the Salsa 1 Head to the Salsa 1 Poles.
Where To Purchase:
- McMaster
- Amazon (Similar to the original supplier, but of a lower quality. Will function identically)
12.9" iPad Pro Salsa 1 Faceplate
This faceplate secures a compatible 12.9" iPad Pro (3rd - 6th Generation) to the Salsa 1 Head.
Where To Purchase:
11" iPad Pro & 10.9" iPad Air Salsa 1 Faceplate
This faceplate secures a compatible 11" iPad Pro (1st - 4th Generation) or 10.9" iPad Air (4th - 5th Generation) to the Salsa 1 Head.
Where To Purchase:
Salsa 1 Poles
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Poles.
Salsa 1 Hinge Knob And Pole Rod Retention Nut
This nut is located within the Salsa 1 Poles and beneath the Salsa 1 Hinge Knobs. It tightens the internal rods, helping to secure the poles to the baseplate, to each other, and to the Salsa 1 Hinge.
Where To Purchase:
Replacement Poles
These replacement poles are used to replace original Salsa 1 poles that have been lost, scratched, or damaged.
Where To Purchase:
Salsa 1 Base Plate
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Salsa 1 Base Plate.
Salsa 1 Base Plate
This replacement base plate is used to replace an original Salsa 1 Base Plate that has been lost, scratched, or damaged.
Where To Purchase:
Salsa 1 Base Plate Feet
These adhesive feet attach to the bottom of the Salsa 1 Base Plate to add grip and stability on various surfaces.
Details:
- 3/4-inch Wide (19.05mm)
- 3/4-inch Long (19.05mm)
- 3/8-inch Tall (9.52mm)
Where To Purchase:
Salsa 1 Base Plate Feet Adhesive
This adhesive tape attaches the Salsa 1 Base Plate Feet to the Salsa 1 Base Plate when the original adhesive has worn out.
Where To Purchase:
IMPORTANT: The adhesive is designed to be used with the Salsa 1 Base Plate Feet and will require trimming, as it does not come pre-cut. For best results, clean the Salsa 1 Base Plate surface thoroughly with a mild solvent before applying.
Atlas Backdrop Stand
Below is a list of all of Photobooth Supply Co.'s official recommendations for replacement parts for the Atlas Backdrop Stand.
Bottom Atlas Stand Pole Screw
These screws attach to the bottom of the Atlas Stand under the feet.
Details:
M8-1.25 x 45mm flat head socket cap screws countersunk bolt
Where To Purchase:
IMPORTANT: Any M8-1.25 screw with a length between 30mm and 50mm is compatible with the bottom pole of the Atlas Stand.
Miscellaneous
Below is a list of all of Photobooth Supply Co.'s official recommendations for miscellaneous parts used with Salsa 1 Photo Booth.
Salsa 1 SKB Carrying Case
This hard-shell carrying case is used to transport the Salsa 1 Booth.
Where To Purchase:
IMPORTANT: The foam inserts included with the original Salsa 1 SKB case are custom-made and proprietary to Photobooth Supply Co.
These custom-made foam inserts are not available for purchase through the Midwest Case Company and are not included if you purchase a new SKB hard shell carrying case directly.
If you need to replace your case, we recommend removing and reusing the original foam from your current Salsa 1 Booth.
If your Salsa 1 carrying case is damaged or needs replacement parts, you can reach out directly to SKB Cases to submit a request.
Top Button/Home Button Tool
This tool is used to press the top button or Home button through the opening in the Salsa 1 Faceplate to activate or exit Guided Access.
Where To Purchase: